View SY84113BUMG_5057666.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SY84113BU
Low Power 2.5V 1.25Gbps Limiting Post Amplifier with Ultra Wide LOS Range
General Description
Features
The SY84113BU low power limiting post amplifier is * Ultra wide LOS Range (5mVpp to 100mVpp) designed for use in fiber-optic optical modules for * Single 2.5V power supply multirate applications up to 1.25Gbps. The device * Ultra low power consumption (55mW typ) connects to a typical transimpedance amplifier (TIA) and * 125Mbps to 1.25 Gbps operation can produce output signals to CML-level waveforms. * Low-noise CML data outputs Intended for the GbE and Fibre Channel applications, the SY84113BU offers a wide LOS range. It is able to * TTL /EN input detect input signals for as low as 5mVpp and as high as * Programmable LOS level (LOSLVL) 100mVpp. The SY84113BU is intended to be used in * Internal 50Ohm termination AC-coupled input applications. * Available in a tiny 3mm x 3mm QFN package The SY84113BU generates a Loss-of-Signal (LOS) open-collector TTL output. A programmable Loss-ofSignal level set pin (LOSLVL) sets the sensitivity of the Applications input amplitude detection. LOS asserts high if the input * Gigabit Ethernet amplitude falls below the threshold set by LOSLVL and de-asserts low otherwise. The enable input (/EN) de* Fibre Channel asserts the true output signal without removing the input * GEPON signal. The LOS output can be fed back to the /EN input to implement the squelch function that maintains output Markets stability under a loss-of-signal condition. The SY84113BU operates on a single 2.5V power * Datacom/telecom supply and offers ultra low power consumption. This * Compact SFP/SFF Optical transceiver device is perfectly suited to meet the stringent power * SFP/SFF Optical transceiver requirements of the CSFP/SFP/SFF optical modules. All support documentation can be found on Micrel's web site at: www.micrel.com. _________________________________________________________________________________________________________
Typical Application
Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com
January 2011
M9999-011711-A hbwhelp@micrel.com or (408) 955-1690
Micrel, Inc.
SY84113BU
Ordering Information
Part Number SY84113BUMG SY84113BUMGTR
Notes: 1. Tape and Reel.
(1)
Package Type QFN-16 QFN-16
Operating Range Industrial Industrial
Package Marking 113B with Pb-Free bar line indicator 113B with Pb-Free bar line indicator
Lead Finish NiPdAu Pb-Free NiPdAu Pb-Free
Pin Configuration
16-Pin (3mm x 3mm) QFN-16
Pin Description
Pin Number 15 Pin Name /EN Type TTL Input Pin Function /Enable: This input enables the outputs when LOW. Internally connected to a 25k pull-up resistor and will default to a logic HIGH state if left open. Differential data inputs. Each input is internally terminated to the VREF pin by a 50 resistor. Reference Voltage: Place 0.1uF capacitor to Vcc to help stabilize LOSLVL DC Input Loss-of-Signal Level Set. A resistor from this pin to VCC sets the threshold for the data input amplitude at which LOS will be asserted. Device ground. Exposed pad must be connected to PCB ground plane. Loss-of-Signal: asserts high when the data input amplitude falls below the threshold set by LOSLVL. Differential data outputs. Unused output should be terminated 50 to VCC. Positive power supply. . Bypass with a 0.1uF || 0.01uF low ESR capacitor as close to VCC pin as possible.
1, 4 6 14
DIN, /DIN VREF LOSLVL
Data Input
2, 3, 10, 11, EPAD 7 12, 9 5, 8, 13, 16
GND LOS /DOUT, DOUT VCC
Ground Open-collector TTL output CML Output Positive Rail
January 2011
2
M9999-011711-A hbwhelp@micrel.com or (408) 955-1690
Micrel, Inc.
SY84113BU
Absolute Maximum Ratings(1)
Supply Voltage (VCC) ....................................... 0V to +4.0V Input Voltage (DIN, /DIN) .......................................0 to VCC Output Current (IOUT) ............................................... 25mA EN Voltage .............................................................0 to VCC VREF Current .......................................... -800A to +500A LOSLVL Voltage................................................. VREF to VCC Lead Temperature (soldering, 20sec.) ..................... 260C Storage Temperature (Ts) ....................... -65C to +150C
Operating Ratings(2)
Supply Voltage (VCC) ......................+2.375 to +2.625V Ambient Temperature (TA).................. -40C to +85C Junction Temperature (TJ)................ -40C to +120C Package Thermal Resistance(3) (JA) Still-air ............................................... 60C/W (JB) ........................................................... 33C/W
DC Electrical Characteristics
VCC = 2.5 5%; TA = -40C to +85C, typical values at VCC = 2.5V, TA = 25C.
Symbol ICC LOSLVL VOH VOL VREF Z0 ZI Parameter Power Supply Current LOSLVL Voltage DOUT, /DOUT HIGH Voltage DOUT, /DOUT LOW Voltage Reference Voltage Single-Ended Output Impedance Single-Ended Input Impedance 40 40 Condition Outputs terminated 50Ohm to Vcc VREF VCC-0.020 VCC-0.005 Vcc - 0.6 50 50 60 60 Min Typ 22 Max 35 VCC VCC Units mA V V V V
VCC-0.475 VCC-0.400 VCC-0.350
TTL DC Electrical Characteristics
VCC = 2.5 5%; TA = -40C to +85C, typical values at VCC = 2.5V, TA = 25C. Symbol
VIH VIL IIH IIL VOH VOL
Parameter
/EN Input HIGH Voltage /EN Input LOW Voltage /EN Input HIGH Current /EN Input LOW Current LOS Output HIGH Level LOS Output LOW Level
Condition
Min
2.0
Typ
Max
Vcc 0.8 20
Units
V V A mA V
VIN = VCC VIN = 0.5V Vcc = 2.5V. IOH < 50uA IOL = 2mA -0.3 2
0.5
V
January 2011
3
M9999-011711-A hbwhelp@micrel.com or (408) 955-1690
Micrel, Inc.
SY84113BU
AC Electrical Characteristics
VCC = 2.5 5%; TA = -40C to +85C, typical values at VCC = 2.5V, TA = 25C.; RLoad = 50 to VCC;
Symbol tr, tf tJITTER VID VOD TOFF TON LOSAL LOSDL HYSL LOSAM LOSDM HYSM LOSAH LOSDH HYSH B-3dB AV(Diff) S21
Notes: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability. 2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings. 3. Package Thermal Resistance assumes exposed pad is soldered (or equivalent) to the devices most negative potential on the PCB. JB uses a 4-layer and JA in still air unless otherwise stated. 4. Amplifier in limiting mode. Input is a 200MHz square wave. 5. Deterministic jitter measured using 1.250 Gbps K28.5 pattern, VID = 60mVPP. 6. Random jitter measured using 1.250Gbps K28.7 pattern, VID = 60mVPP. 7. See "Typical Operating Characteristics" for a graph showing how to choose a particular RLOSLVL for a particular LOS assert and its associated de-assert amplitude. 8. This specification defines electrical hysteresis as 20log (LOS De-Assert/LOS Assert). The ratio between optical hysteresis and electrical hysteresis is found to vary between 1.5 and 2 depending upon the level of received optical power and ROSA characteristics. Based on that ratio, the optical hysteresis corresponding to the electrical hysteresis range 2dB-4.5 dB, shown in the AC characteristics table, will be 1dB-3dB Optical Hysteresis. 9. In real world applications, the LOS Release/Assert time can be strongly influenced by the RC time constant of the AC-coupling cap and the 50 input termination. To keep this time low, use a decoupling cap with the lowest value that is allowed by the data rate and the number of consecutive identical bits in the application (typical values are in the range of 0.001F to 1.0F).
Parameter Output Rise/Fall Time (20% to 80%) Deterministic Random Differential Input Voltage Swing Differential Output Voltage Swing LOS Release Time LOS Assert Time Low LOS Assert Level Low LOS De-assert Level Low LOS Hysteresis Medium LOS Assert Level Medium LOS De-assert Level Medium LOS Hysteresis High LOS Assert Level High LOS De-assert Level High LOS Hysteresis 3dB Bandwidth Differential Voltage Gain Single-Ended Small-Signal Gain
Condition Note 4 Note 5 Note 6
Min
Typ 150 15 5
Max 260
Units ps psPP psRMS
5 Note 4 Note 9 Note 9 RLOSLVL = 10k, Note 7 RLOSLVL = 10k, Note 7 RLOSLVL = 10k, Note 8 RLOSLVL = 5k, Note 7 RLOSLVL = 5k, Note 7 RLOSLVL = 5k, Note 8 RLOSLVL = 100, Note 7 RLOSLVL = 100, Note 7 RLOSLVL = 100, Note 8 2 2 60 2 7 700 800 2 2 3.9 5.6 3.1 9.2 13.6 3.4 73 103 3.0 850 38 26 32
1800 950 10 10
mVPP mVPP uS uS mVPP mVPP
4.5 16 4.5 130 4.5
dB mVPP mVPP dB mVPP mVPP dB MHz dB dB
January 2011
4
M9999-011711-A hbwhelp@micrel.com or (408) 955-1690
Micrel, Inc.
SY84113BU
Typical Functional Characteristics
VCC = 2.5 5%; TA = -40C to +85C, typical values at VCC = 2.5V, TA = 25C.; RLoad = 50 to VCC;
Typical Operating Characteristics
VCC = 2.5 5%; TA = -40C to +85C, typical values at VCC = 2.5V, TA = 25C.; RLoad = 50 to VCC;
LOS Assert/De-Assert Levels
1000 6 5 Amplitude (mV) 100 Hysteresis (dB) 4 3 2 1 0.1 1 LOSLVL Resistor (KOhm) 10 1 0.1 1 LOSLVL Resistor (KOhm) 10
LOS Hysteresis
10
January 2011
5
M9999-011711-A hbwhelp@micrel.com or (408) 955-1690
Micrel, Inc.
SY84113BU
Functional Block Diagram
Detailed Description
The SY84113BU is a high-sensitivity limiting post amplifier that operates from a single +2.5V power supply over temperatures from -40C to +85C. Signals with data rates up to 1.25Gbps, and as small as 5mVpp, can be amplified. Figure 1 shows the allowed input voltage swing. The SY84113BU generates a LOS output signal that can be fed back to /EN for output stability in the absence of a signal at the input. LOSLVL sets the sensitivity of the input amplitude detection. SY84113BU offers ultra wide LOS detection range. This allows the device to be used in multiple AC-coupled applications. Input Amplifier/Buffer Figure 2 shows a simplified schematic of the input stage. The high-sensitivity of the input amplifier can detect and amplify AC-coupled signals as small as 5mVpp to full CML output level. The input stage also can allow signals as large as 1800mVpp. Input signals are amplified with a typically 38dB differential voltage gain until they reach the limiting mode of the amplifier. SY84113BU outputs in standard 400mV CML output levels. Output Buffer The SY84113BU's CML output buffer is designed to drive 50 lines and is internally terminated with 50 to VCC. Figure 3 shows a schematic of the output stage.
Loss-of-Signal The SY84113BU generates a chatter-free loss-of-signal (LOS) open-collector TTL output as shown in Figure 4. LOS is used to determine that the input amplitude is too small to be considered as a valid input. LOS asserts high if the input amplitude falls below the threshold set by LOSLVL and de-asserts low otherwise. LOS can be fed back to the enable (/EN) input to maintain output stability under a loss of signal condition. /EN de-asserts low the true output signal without removing the input signals. Typically, 3dB LOS hysteresis is provided to prevent chattering. Loss-of-Signal-Level Set A programmable LOS level set pin (LOSLVL) sets the threshold of the input amplitude detection. Connecting an external resistor between VCC and LOSLVL sets the voltage at LOSLVL. This voltage ranges from VCC to VREF. The external resistor creates a voltage divider between VCC and VREF, as shown in Figure 5. Hysteresis The SY84113BU provides typically 3dB LOS electrical hysteresis, which is defined as 20log (VINLOS-Assert / VINLOS-De-Assert). Since the relationship between the voltage out of the ROSA to optical power at its input is linear, the optical hysteresis will be typically half of the electrical hysteresis reported in the datasheet, but in practice the ratio between electrical and optical hysteresis is found to be within the range 1.5-1.8. Thus 3dB electrical hysteresis will correspond to an optical hysteresis within the range 1.7dB - 2dB. 6
M9999-011711-A hbwhelp@micrel.com or (408) 955-1690
January 2011
Micrel, Inc.
SY84113BU
Figure 1. VIS and VID Definition
Figure 2. Input Structure
Figure 3. Output Structure
Figure 4. LOS Output Structure
Figure 5. LOSLVL Setting Circuit
Note: Recommended value for RLOSLVL is 15k or less.
January 2011
7
M9999-011711-A hbwhelp@micrel.com or (408) 955-1690
Micrel, Inc.
SY84113BU
Package Information
16-Pin (3mm x 3mm) QFN (QFN-16)
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com
Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel's terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2010 Micrel, Incorporated.
January 2011
8
M9999-011711-A hbwhelp@micrel.com or (408) 955-1690

▲Up To Search▲

Price & Availability of SY84113BUMG

	To Download SY84113BUMG Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .